Reusable Floating Beads with Immobilized Xylose-Fermenting Yeast Cells for Simultaneous Saccharification and Fermentation of Lime-Pretreated Rice Straw

Novel bioreactor beads for simultaneous saccharification and fermentation (SSF) of lime-pretreated rice straw (RS) into ethanol were prepared. Genetically modified Saccharomyces cerevisiae cells expressing genes encoding xylose reductase, xylitol dehydrogenase, and xylulokinase were immobilized in calcium alginate beads containing inorganic lightweight filler particles to reduce specific gravity. For SSF experiments, the beads were floated in slurry composed of lime-pretreated RS and enzymes and incubated under CO₂ atmosphere to reduce the pH for saccharification and fermentation. Following this reaction, beads were readily picked up from the upper part of the slurry and were directly transferred to the next vessel with slurry. After 240 h of incubation, ethanol production by the beads was equivalent to that by free cells, a trend that was repeated in nine additional runs, with slightly improved ethanol yields. Slurry with pre-saccharified lime-pretreated RS was subjected to SSF with floating beads for 168 h. Although higher cell concentrations in beads resulted in more rapid initial ethanol production rates, with negligible diauxic behavior for glucose and xylose utilization, no improvement in the ethanol yield was observed. A fermentor-scale SSF experiment with floating beads was successfully performed twice, with repeated use of the beads, resulting in the production of 40.0 and 39.7 g/L ethanol. There was no decomposition of the beads during agitation at 60 rpm. Thus, this bioreactor enables reuse of yeast cells for efficient ethanol production by SSF of lignocellulosic feedstock, without the need for instruments for centrifugation or filtration of whole slurry.     

Removal and repair techniques for thermal barrier coatings: a review

ABSTRACT

A comprehensive literature review of the existing techniques for removing and repairing of damaged thermal barrier coatings is presented, with the focus on top ceramic coats. The advantages and disadvantages of each technique are compared and assessed. The review shows that there is not a universal method applicable to all coating systems. The selection of the coating removal and repair process must be specific to damaged coating systems, based on their composition, type of damages, and available resources. This review will provide some inside look at various approaches in an effort to meet the different coating repair needs.     

半干法烟气脱硫脱硝除尘一体化技术在焦化厂中的应用

介绍了焦化厂半干法烟气脱硫脱硝除尘一体化技术在焦化厂中的应用,描述了半干法烟气脱硫、低温选择性催化还原法(SCR)脱硝+除尘一体化工艺流程,该工艺运行效果、运行参数、工艺技术的特点,运行中常见问题及解决方法和未来需要进一步思考和解决的问题等。实践证明,该工艺技术在焦化厂能够长期稳定运行,脱硫脱硝及除尘效果较好,烟气指标可达到环保要求。     

Predicting pollutant removal in constructed wetlands using artificial neural networks(ANNs)

Growth in urban population,urbanisation,and economic development has increased the demand for water,especially in water-scarce regions.Therefore,sustainable approaches to water management are needed to cope with the effects of the urbanisation on the water environment.This study aimed to design novel configurations of tidal-flow vertical subsurface flow constructed wetlands(VFCWs) for treating urban stormwater.A series of laboratory experiments were conducted with semi-synthetic influent stormwater to examine the effects of the design and operation variables on the performance of the VFCWs and to identify optimal design and operational strategies,as well as maintenance requirements.The results show that the VFCWs can significantly reduce pollutants in urban stormwater,and that pollutant removal was related to specific VFCW designs.Models based on the artificial neural network(ANN) method were built using inputs derived from data exploratory techniques,such as analysis of variance(ANOVA) and principal component analysis(PCA).It was found that PCA reduced the dimensionality of input variables obtained from different experimental design conditions.The results show a satisfactory generalisation for predicting nitrogen and phosphorus removal with fewer variable inputs,indicating that monitoring costs and time can be reduced.     

Carrier lifetime regulation strategy to improve the sewage purification capacity of superhydrophobic silver phosphate fabric

Sewage contains a variety of components including oil slick and water-soluble pollutants. How to remove different types of pollutants at the same time is a challenge. In this paper, superhydrophobic fabric (SH fabric) was prepared by the combination of silver phosphate photocatalyst with fabric substrate. Surface oil slick and rhodamine B contaminants can be removed simultaneously by SH fabric. The degradation efficiency after three cycles is still maintained above 90% under outdoor light source conditions. In order to improve the degradation efficiency of silver phosphate photocatalyst, ethanol/water mixed solvent was used. And the reasons for the improvement of catalyst performance were studied systematically. It is found that the charge transfer resistance of the silver phosphate catalyst prepared by addition of ethanol (S-3) decreases, while the carrier concentration and lifetime increase. The VB and CB of silver phosphate with the best degradation performance (S-3) are 2.425 eV and 0.135 eV, respectively. It is hoped that this SH fabric could provide a new solution to the improvement of catalyst performance and comprehensive treatment of sewage.     

Modeling of dibenzothiophene oxidative desulfurization using response surface methodology

The effect of reaction temperature, mixing speed and oxidant to catalyst volume ratio, including their interactions on the oxidative desulfurization of dibenzothiophene by using response surface methodology was studied. Hydrogen peroxide was used as oxidant and acetic acid as catalyst. The obtained model accurately predicts conversion of dibenzothiophene and the best conversion of 98.7% was observed at temperature 70°C, mixing speed of 1250 rpm and oxidant to catalyst volume ratio of 1:1. At high temperatures, a major limitation of the desulfurization process is the mass transfer and the high mixing speed is needed to achieve an efficient process.     

Droplet dynamics in a proton exchange membrane fuel cell flow field design with 3D geometry

Water management is crucial to achieve both high-performance and durability of proton exchange membrane fuel cell (PEMFC). Therefore, it is necessary to investigate the dynamic behavior of droplets in PEMFC channel for water management. In this paper, we explore the kinetics of droplets in a 3D flow field by experimental and theoretical analysis. More specifically, we examine the following four perspectives: 1) the movement and falling of droplets, and their force and deformation, 2) the superiority of 3D flow field drainage, 3) the pressure and viscous force under different scenarios including varying droplet sizes and velocities, and 4) the expression describing the shape change of droplets. The results show that the 3D flow field has a greater driving force on droplets and that their deformation affects the discharge of liquid water. Throughout the study, we provide better understanding of droplet dynamic in PEMFC gas channels. It enables to optimize the design and working conditions of these channels.     

Simultaneous bioelectricity generation and pollutants removal of sediment microbial fuel cell combined with submerged macrophyte

A submerged macrophyte sediment microbial fuel cell (SP-SMFC) was constructed in this study. Ceratophyllum demersum L., Vallisneria natans, Hydrilla verticillate were chosen as the submerged plants to form cer-SMFC, val-SMFC, hyd-SMFC systems. Plant groups showed the advantage of bioelectricity generation and pollutants removal compared with the unplanted system. The cer-SMFC group stood out with the maximum power density as 24.56 mW m^?2 and the average pollutants removal in overlying water (COD: 81.16%, TN: 65.27%, TP: 79.10%) and in sediments (TN: 26.40%, TP: 21.79%). The determination of root exudates and radial oxygen loss (ROL) demonstrated that C. demersum L. was superior to other studied submerged macrophytes. More root exudates may contribute to an increase in available substrates for electrochemically active bacteria and other microorganisms. Higher enzyme activities were obtained in three SP-SMFCs (especially in cer-SMFC). ATPase and APA activities in cer-SMFC group were increased by over 40% compared with the control. The results indicated that the presence of plants enhanced the microorganism activities, thereby improving bioelectricity generation and pollutants removal. This study will facilitate the application of SP-SMFC technology as an alternative for in situ remediation of polluted sediments.